Видео

Why don't you make the catcher hook before you mount and wind on the mandrel ?

whats that drill chuck thing you use to wind them?

Very amazing

Step 1: buy a lathe. Just kidding. Thanks for making this. I can use a hand drill instead.

by hand, you say... hmmm....

Watching your videos saved me from having to drive to the nearest large town to get some springs I badly needed, and the money in gas plus the cost of the factory springs. Thank you for posting these videos.

That's very helpful. Thanks.

That is a very helpful thing to know! Churs!

Parabéns!!’ Mais um inscrito do Brazil

It would be nice to learn what wire is required for that, and could you, e.g. «temper» or «harden» a soft wire to make it springworthy, and should it be before or after the bending. Thank you.

Thanks for your great videos, really appreciate fundamental knowledge from the expert. Could you tell us more about the stress release afterwards, please? 👍

Didn’t like this at all . The way it pulled that back at the end was dreadful and quill won’t last long .

Don't you have to harden then temper them?

Quick question, i just made a replacement slide stop spring for my gun using a paper clip, its working fine right now, was wondering if is should heat treat it?

Great! subscribed.

Thanks! super interesting! what is the time/temp for the pressure relief in the oven?

Very good, dont speak any word You teacheme to make spring very good. One day I will visit to You in Australia. Thankyou very much

I have heard SPP works best when the coils are not touching and I expect with a "certain" spacing between coils. A thought - select a bolt or piece of threaded rod of a certain? length and diameter with a certain? thread spacing, grind flats (3? flats or 4? flats) along the length leaving a small section of threads between each flat to establish coil spacing. OR position a piece of threaded rod as a coil spacing guide very close to the "spinning diameter" of the winding mandrel

Great! But what about hardening?

Good

what about thin wire and smaller wire diameter?

Is it possible to get pliers for bending spring ends like those in one of your videos?

Are you interested in spring machine?

I've watched a number of how to make springs videos in the normal course of watching maker/machining vids on YT. Until recently, haven't needed to try; my big box of springs, combined w/ never throwing springs away has served me well. Then I needed to repair a shop vac motor exposed to moisture & age. It needed torsion brush springs wound opposite to every torsion spring I had or could buy of the right gauge wire. About to start manufacturing the type of apparatus I've seen numerous times, this morning, in a few hours, I decided to take another look through YT vids. Am I glad I did. You have saved me several hours of machining & assembly I was about to invest in $0.20 springs. Thanks for sharing your knowledge. GeoD

Thank you for the great videos. I wanted to ask, does the number of coils on a torsion spring have any effect on the performance/stiffness?

Hi, I’ve been looking for a method to calculate the spring ‘size, strength’ required to ‘balance’ an articulated arm dependent on the weight it needs to support. Can anyone point me in the right direction?

Hi, do you sell this packing, im very interested in getting some, im in australia and dont want to order from over seas.

Sir ye machin kha se me le gi

where can you buy such ticks?

when I think that back in the 80s we trashed our toys just because we weren't able to replace or make a new replacement spring . hey !! I remember cassettes players door too , when the spring was damaged you had to manually open it

Good work

Eres un crak , el REY DE LOS MUELLES, ¿Se pueden templar los muelles?

Nice and simple. Thanks for making the video.

Thank you very much for showing your knowledge and skills, congratulations, good video

Very admirable! This setup is quiet, light and not power hungry. Perfect for the home shop in the city. I have looked everywhere online to purchase a similar unit but to no avail. The only equipment I have found which comes close is a Carlson sc-1. However these units are manually driven. If you know of any suppliers the info would be greatly appreciated. Love your videos.!!

What wire is used for springs

Thanks for providing this material

Nice work. Thankyou.

Can you give instructions on how to continue running when there is a sudden power outage?

what makes these square springs so perfect for reflux distillation?

satisfying

Witchcraft!! Sorcery! Also thanks for these excellent tutorials.

Visitor from Marius Hornberger. Quite a lovely and easy set-up. Just buy a chuck, and a piece of wood to stick it through and a handel, and you can make springs in the garage! :)

Thanks to your excellent tutorials, I was able to make the wire catch and then wind the new torsion spring I needed and I'm quite pleased with how it turned out.🧬

Wow looks simple when you know how. Will be giving this a go later. Thanks for the knowledge

thanks man

Total waste of time. All demonstration and no explanation.... us rookies are totally in the dark because of your ego and arrogance

English hook bending tool

Un fenomeno maestro

Un fenomeno ,fácil y efectivo suscrito